Freshwater Flushing Adds Years to the Life of an Outboard

 

Freshwater Flushing Adds Years to the Life of an Outboard

 

Most of us take good care of our marine equipment. We wash and wax our boats and outboards, change the oil and oil filter regularly, and replace the fuel filters, but what about your outboard’s cooling system. Unfortunately, it is often overlooked in a maintenance regimen.

BoatersLogVol5No2FreshwaterFlush041113image5

During the course of normal use, the water pump can ingest mud, sand, and silt, which then flows through the engine. Marine growth can also occur behind the inlet screens interrupting the flow of water to the engine.  Over time, debris can accumulate in the outboard’s cooling passages. This build up can damage the water pump’s rubber impeller and plastic housing.  Eventually, the buildup can also restrict the amount of water available to the engine resulting in poor cooling, which will damage the engine. It may even promote corrosion in the exhaust system because increased engine temperatures—along with the effects of using ethanol blended fuels—can cause increased exhaust temperatures.

 

Freshwater Flushing Facts 

The outboard should be flushed after every use in salt or dirty water. Freshwater flushing with clean water will dislodge most contaminants (sand, silt, mud, etc.) and force them out of the passages in the cooling system. Perhaps even more importantly, flushing removes salt buildup, which can lead to poor cooling as well as corrosion of the engine block and midsection.

 

Generically speaking, there are three methods to flush an outboard: using a flush bag, flush muffs or the freshwater flushing attachment built into the outboard.

 

Flush Bag Method

BoatersLogVol5No2FreshwaterFlush041113image1

What:  A flush bag is a sturdy collapsible bag that fits under the lower unit of the outboard and fills with water.  Submerging the gearcase allows the motor to take in cooling water from the inlet screens and return it to the bag through the propeller. There are different bag designs; some are designed to be used with the boat moored.

 

Where: Use the Flush Bag method with the boat on a trailer or the boat moored. It requires running the engine (but only after the bag is filled with water). Outboards with more than one inlet on each side of the lower unit should be flushed using this method.

 

How:

  • Trim the outboard to the vertical position
  • Remove the propeller
  • Screw the garden hose into the connector on the bag and fill the bag
  • Make sure the water level is as high as possible above the cooling water inlets on the lower unit. This will assure that the water pump is completely submerged
  • Start the outboard and set the throttle to no more than a fast idle (800-900 RPM max)
  • Watch for water coming out of the pilot tube at the lower rear of the cowling. Run the engine for 10-15 minutes. Note: it may take 20–30 seconds to fill the water passages before water will exit the pilot tube
  • Stop the engine and turn off the faucet
  • Never run the engine without cooling water
  • Turn the freshwater on before starting the engine; turn the water off after stopping the engine
  • Add water to the flush bag while the motor is running to maintain the maximum water level
  • Do not leave the outboard unattended while running

 

Flush Muff Method 

(For models with single inlet lower units)

BoatersLogVol5No2FreshwaterFlush041113image2

What: Flush muffs are rubber cups that fit over the water inlet on the gearcase (one of the cups has a hose fitting). They require running the engine (but only after the garden hose is in place and water running).

 

Where: Best done with the boat on a trailer or a lift, completely out of the water.

 

How: 

  • Trim the outboard to the vertical position
  • Remove the propeller
  • Screw the garden hose onto the flush muff connector
  • Place the flush muffs over the water inlets on gearcase
  • Turn the water on slowly, until you can see a bit of water leaking from around the flush muff rubber cups
  • Check to ensure the rubber cups are still in place over the inlets
  • Start the outboard and set the throttle to no more than a fast idle (800-900 RPM max)
  • Watch for water coming out of the pilot tube at the lower rear of the cowling. Increase the water flow, if necessary, to maintain a flow of water    from the pilot tube. Note: it may take 20–30 seconds to fill the water passages before water will exit the pilot tube
  • There should be some water exiting the back of the gearcase, through the exhaust also
  • Run the engine for 10-15 minutes
  • Stop the engine and turn off the faucet

 

Never run the engine without cooling water. Turn the freshwater on before starting the engine; turn the water off after stopping the engine. Running the outboard with little or no cooling water will cause expensive overheating damage in a very short time. Don’t rev the engine while using flush muffs, because there isn’t enough water flow/pressure to sufficiently cool the engine at high rpm.

 

Built-In Flushing Device

BoatersLogVol5No2FreshwaterFlush041113image4

What: A built-in flushing device is a hose fitting, usually located near the lower rear cowling.  Do not run the engine during this procedure.

 

Where: An outboard can be flushed with the boat on a lift or in the water; it works best if you can trim the engine up so the gearcase is out of the water.

 

How: 

  • Connect a garden hose to the outboard’s flushing device fitting
  • Turn on the faucet; let freshwater run through the outboard for 10-15 minutes
  • Turn off the faucet; disconnect
  • Put the cap back on engine’s flush fitting (per owner’s manual)

 

Which Method to Use 

There is no single best method for flushing an outboard motor. There are only best methods to suit the circumstances. For example, the flush attachment method is the easiest and quickest for a boat that is moored, while the flush bag method is particularly useful on motors with multiple inlets per side. In addition, the flush muff method and bag method are the only methods to use when fogging the engine for winter storage.

 

Testing has shown that even the flush attachment method allows water to pass into the cylinder head passages, in spite of the fact that the thermostat does not fully open. This means that there is no disadvantage to using the flush attachment.

 

While conventional wisdom might indicate there is some benefit to flushing with the engine running—such as with flush muffs or a flush bag—there is no clear data to indicate this is true.

 

What’s important is to in all cases, regularly check to see that water inlet screens on the lower unit are clear and clean. Flushing your outboard with freshwater on a regular basis can go a long way toward extending the outboard’s life span – especially for those who boat in saltwater. Freshwater flushing is easy and cheap, so keep the garden hose handy. Y

 

Original Source: Yamaha Outboards.com

More Stories & Fun Things to Do

Travel

Vacation Locations: Knowledge is Fun Too!

Most children (and adults, too) will either roll their eyes or sigh when, while speaking about vacation locations, the word “learning” just happens to be mentioned. Yes, it is a fact that school trips take all of us during our younger years to everything from museums to libraries to historic locations in order to teach us things we should know. But when thinking about your vacation, you should know that by considering journeying to a particular place that just happens to register high on the historical or educational meter, you could have even more fun.

Business

Is Social Media Still Growing?

It was in 1999, Bill Gates wrote a book titled, “Business @ the Speed of Thought.” Within these pages, the man who became the computer world’s wizard made massively bold predictions that, at the time, sounded ridiculous and outrageous to those who read them. But when you look at how the social media realm has grown over the past few decades, it is important to take note that not only did his predictions from 1999 come true, but they are also responsible for seeing social media continue to grow by leaps and bounds to this day.

Entertainment

Bawdy Road Romp Opens as #1 Comedy at the Box Office

Universal Pictures\’ Girls Trip made a spectacular debut on its opening weekend, raking in over $30 million at the box office. The hilarious road romp, directed by Spike\’s cousin Malcolm Lee (The Best Man), co-stars Regina Hall, Queen Latifah, Tiffany Haddish and Jada Pinkett Smith.

Health

Making Your Health “Resolute”

It is time for those New Year’s Resolutions to be made

Books

Book of Black Heroes

“The first African-American political leaders began to serve following the Civil War…Known as Reconstruction, this period represented a window of opportunity for African-Americans… Many [Black] political leaders emerged during this period, using their political power and influence to push for equality and justice for all Americans… Unfortunately, the Reconstruction period was short-lived, lasting only from 1865-1877.